關于RM22TG20繼電器的主要參數，你了解多少？

　　RM22TG20繼電器一般由鐵芯、線圈、銜鐵、觸點簧片等組成的。只要在線圈兩端加上一定的電壓，線圈中就會流過一定的電流，從而產生電磁效應，銜鐵就會在電磁力吸引的作用下克服返回彈簧的拉力吸向鐵芯，從而帶動銜鐵的動觸點與靜觸點結合。
　　
　　當線圈斷電后，電磁的吸力也隨之消失，銜鐵就會在彈簧的作用下恢復到原來的位置，使動觸點與原來的靜觸點斷開。從而達到了在電路中的導通、切斷的目的。
　　
　　繼電器一般配置有輔助觸點，所謂常開觸點，就是繼電器線圈未通電時處于斷開狀態的觸點；所謂常閉觸點，就是線圈未通電時處于導通狀態的觸點。繼電器線圈得電動作，常開觸點會閉合，常閉觸點會斷開。繼電器從本質上講就是以小電流控制大電流，這一點與接觸器類似。
　　
　　RM22TG20繼電器的主要參數：
　　
　　額定工作電壓：是指繼電器正常工作時線圈所需要的電壓。根據繼電器的型號不同，可以是交流電壓，也可以是直流電壓。
　　
　　吸合電壓：使繼電器觸點吸合的zui小線圈電壓（從小到大測試）。
　　
　　釋放電壓：保證繼電器觸點釋放的zui大線圈電壓（從大到小測試）。
　　
　　吸合電流：是指繼電器能夠產生吸合動作的zui小電流。在正常使用時，給定的電流必須略大于吸合電流，這樣繼電器才能穩定地工作。而對于線圈所加的工作電壓，不要超過額(e)定工作電壓的1.5倍，否則會產生較大的電流而把線圈燒毀。
　　
　　釋放電流：是指繼電器產生釋放動作的zui大電流。當繼電器吸合狀態的電流減小到一定程度時，繼電器就會恢復到未通電的釋放狀態。這時的電流遠遠小于吸合電流
　　
　　接觸電阻：是指繼電器中接點接觸后的電阻值，可以通過萬用表測量。對于許多繼電器來說，接觸電阻無窮大或者不穩定是zui大的問題。